How do I know if my pool chlorinator is working?

The easiest way to be certain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights on the chlorinator box. When operating, you should also see bubbles (hypochloride gas) inside the chamber, producing what looks like cloudy water – that’s chlorine being created!

On the chlorinator box there should be a light or dial that indicates it is working. Take your test kit and place your thumb over the test tube. Then place it right into the eyeball and take the water. Test the water that water has just left the chlorinator – it should have a very high chlorine reading.

Similarly, how long does a salt chlorinator cell last? about five years

Additionally, why is my chlorinator not making chlorine?

A salt chlorinator cannot produce enough chlorine to do this task. Seek assistance from your local pool shop for the required procedure for your pool. Algae is the most common cause of low or zero chlorine levels.

What should pool chlorinator be set at?

5 Maintenance Tips for Salt Chlorine Generators To make your salt water chlorinator last, you’ll need to perform regular maintenance on it just as you do every other part of your pool. Try to maintain a consistent salt level of between 2,700 parts per million (ppm) and 3,400 ppm, with 3,200 ppm being ideal.

What causes a salt cell to fail?

Salt cells fail for a few different reasons, the main reason being lack of proper maintenance. It is very important to check the cell regularly for excessive buildup. Use a cleaning kit designed for salt cells to keep the plates clear of buildup. Another common cause of salt cell failure is improper water balance.

How much does it cost to replace a salt cell?

Replacing the salt cell costs $700–$1100. Replacing the control board costs $500–$900. You can extend the lifespans by maintaining a consistent salt level, cleaning the cell only when needed, and using the reverse polarity function.

How do I know if my salt generator is working?

The easiest way to be certain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights on the chlorinator box. When operating, you should also see bubbles (hypochloride gas) inside the chamber, producing what looks like cloudy water – that’s chlorine being created!

Can a salt cell be repaired?

Salt Chlorine Generators do require some maintenance and repair. The salt cell will eventually lose performance and the controller circuit boards can develop problems over time. New technology in salt systems may also sway your decision to repair or replace your salt chlorinator.

What temp does chlorine stop working?

Many salt chlorinators have a temperature sensor, which automatically reduces chlorine production when temperatures drop below 60 degrees, and stops production altogether when water temps reach 50 degrees.

When should you replace a salt cell?

Most salt chlorine generators have a salt cell that lasts typically from 3 to 5 years, you should check with the manufacturer to double check the life expectancy. Most salt chlorine systems come with a control panel or a self regulating system that will tell you when the cell needs to be cleaned or replaced.

What percentage should my salt cell be set at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

How often do you have to clean the cell of a salt chlorinator?

The number one maintenance item for a salt water chlorinator is to clean the salt cell regularly, every 2-6 months, but only as needed. Mineral deposits bridge the space between the metal plates, and not just in hard water areas.

How do I know if my salt cell is bad?

If the salt cell does not bubble, then you either have no power to the cell or you have a bad cell. Further troubleshooting will be required. If the salt cell bubbles, but only a little bit, then you probably have a bad cell.

How do I turn off my chlorinator?

Remove the pool chlorinator feeder cap by turning the cap counter-clockwise. When removing the cap, do not stand above the feeder and DO NOT INHALE the chlorine fumes rising from the open feeder. You may need a lever to help twist off the cap.

How do you clean a cell chlorinator?

How to Clean your Salt Water Chlorinator Cell Make a cleaning mixture of 1/10 parts Hydrochloric Acid to water (always add Hydrochloric acid to water). Turn the filtration system off. Remove Salt Cell from the housing. Add the Salt Cell to the cleaning mixture making sure there is little to no contact with the terminals.