How do you set up a Balboa hot tub?

To program, press “Temp,” then “Jets 1.” Press “Temp” to adjust. Press “Jets 1” to exit programming. For non-circ systems, low-speed pump 1 and the ozone generator (if installed) run during filtration. For 24 hour circulation systems, the circ pump and the ozone generator (if installed) run 24 hours.

To program, press “Temp,” then “Jets 1.” Press “Temp” to adjust. Press “Jets 1” to exit programming. For non-circ systems, low-speed pump 1 and the ozone generator (if installed) run during filtration. For 24 hour circulation systems, the circ pump and the ozone generator (if installed) run 24 hours.

Also Know, how do you turn the temperature up on a Balboa hot tub? To change the set temperature, press a temperature button again before the display stops flashing. Each press of “Warm” or “Cool” will adjust the set temperature. After three seconds, the display will stop flashing and begin to display the current spa temperature.

Additionally, what mode should my hot tub be in?

Note: Economy mode should only be used if you are not planning on using the hot tub for two or more days, any less than that and it is more efficient to keep it at a set temperature. You can instead lower the set temperature by 2 degrees.

Where is the drain on a Balboa hot tub?

How to Drain a Balboa Hot Tub

  1. Switch the circuit breaker connected to your Balboa hot tub to the “Off” position. If you are unsure as to which breaker correlates to the hot tub, turn off the main breaker.
  2. Remove the cover from the front of the drain spigot. Secure a hose onto the spigot.
  3. Run the hose to a drain or onto your lawn.

How much is a circuit board for a hot tub?

Hot Tub and Spa Circuit Board Replacement Parts Brand Price Balboa Water Group $259.95

How long does it take a Balboa hot tub to heat up?

about 4 hours

What does code SL mean on hot tub?

If the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles. Other Heating Modes are Standard, Standard in Economy, and Sleep Modes. Ecn or Ec is ON Solid (Not Flashing):

What does sn mean on a hot tub?

SN usually means the sensors are out of sync – they are giving different temperature readings to the circuit board. Balboa allows up to a 2 degree variance in temperature between the sensors, than assumes the tub is heating unevenly and shuts down the tub to prevent damaging it.

How long does it take for a hot tub to heat up?

approximately 4 hours

How do I reset my hot tub control panel?

How to Reset a Spa Heater Locate the spa’s high-limit reset. This is a red button found on many spa packs. Press the high-limit reset button. Turn on your spa and observe its operation. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.

How do you unlock Balboa in hot tub control panel?

Spas using Balboa control systems Locking the panel : Press “Time”, “Blower” and “Warm” within 3 seconds. Unlocking the panel : Press “Time”, “Blower” and “Cool” within 2 seconds. Locking the temperature : Press “Warm”, “Time”, “Blower” and “Warm” within 3 seconds.

What are air controls on a hot tub?

Hot tub air controls, which are located at the top of your spa, manage the force of your jets, the air to water ratio, and mix. They act as an air valve, allowing the spa user to dial in that perfect mix and ratio, increasing the action and pressure from the jets in your spa.

How do you change the mode on a Balboa hot tub?

Balboa Controller VS500Z and VS501Z Mode Settings for Standard, Economy and Sleep. Mode is changed by pressing the Temp or Set button, and then pressing the Light button. If there are UP and DOWN buttons, use the UP button. Do not press the buttons at the same time.

Who makes evolution hot tubs?

2. Evolution Spas – manufactured by Strong Spas, in Northumberland Pennsylvania. The Strong brand is well known amongst independent hot tub dealers across the country and more so on the east coast where it has a more dominant presence.

What temperature should I set my hot tub when not in use?

The general rule of thumb for temperature is that when not in use, the temperature should be set to about 5 degrees lower than when in use. Depending on the climate, this is necessary to keep the water warm enough to reach operating temperature quickly and without wasting energy when the time comes.