The Water Well Board suggests that the minimum water supply capacity for use inside a home should be at least 600 gallons within a two-hour period, or about 5 gallons per minute for 2 hours. Here you will find a chart that describes the water flow rate recommendations further.

A toilet will normally use about 2-3 **gallons per minute** (**gpm**), a shower from 1.5 to 3.0 **gpm**, a bathroom or kitchen faucet from 2-3 **gpm**, a dishwasher from 2-4 **gpm**, and a washing machine from 3-5 **gpm**.

Additionally, is 6 gallons a minute a good well? For a **well**, the yield is considered the maximum rate in **gallons** per **minute** (GPM) that a **well** can be pumped without lowering the water level in the borehole below the pump intake. For most single-family homes, a minimum flow of **6** GPM is suggested from a **well** or spring.

Just so, what is a good well yield?

5 gpm (two fixtures running simultaneously at 2.5 gpm) is a **good** estimate of peak demand, for the typical household. Water wells that reliably **yield** 5 gpm should be able to meet peak and daily needs for most residences. Wells yielding less than 5 gpm, however, are sometimes the only water source available.

Is 50 gpm good for a well?

**50 GPM** is excellent. God Bless our brave men, bring them home, safe again.

### Is 2.5 gallons per minute good?

GPM means Gallons Per Minute. Also known as “flow rate”, GPM is a measure of how many gallons of water flow out of your shower head each minute. Since 1992, a maximum of 2.5 GPM is the federally mandated flow rate for new shower heads. This means no more than 2.5 gallons of water should flow out each minute.

### Is 4 gallons per minute a good well?

The Water Well Board and the New Hampshire Water Well Association, a group of private professionals associated with the well water industry, both recommend a flow rate of 4 gallons per minute for a 4 hour period. That’s equivalent to 960 gallons of water flowing steadily for 4 hours.

### Is 15 gpm good for a well?

The easiest case would be a well that produces a lot of water. This would normally be over 15 gpm (gallons per minute). Since most house pumps won’t pump this much water, the supply can easily meet the demand. In all cases, as the water level in the well drops, you will get less flow and pressure.

### How many GPM is 60 psi?

For water conservation purposes, the Federal Energy Policy Act of 1992 requires that all lavatory (bathroom) faucets sold in the U.S. have a flow rate of no more than 2.2 GPM at a water pressure of 60 psi (pounds per square inch). According to the same law, showerheads may have a maximum flow rate of 2.5 GPM.

### Does GPM affect water pressure?

Shower heads are measured by flow—the number of gallons they deliver per minute (gpm). Flow is affected by water pressure, measured in pounds per square inch (psi). Water pressure on the high side—80 psi, for example—will push a greater amount of water through a shower head than low water pressure, say 20 psi.

### How do you calculate gallons per minute?

To determine GPM using a larger container take the container capacity in gallons, divided it by the number of seconds needed to fill container, then multiply times 60. The result is the GPM. Example: Using a 5 gallon container it takes 14 seconds to fill the container. 5 / 14 X 60 = 21.4 GPM.

### How many gpm does a sink use?

Quick Fixes for Faucet Flow Rate The average flow rate of a kitchen faucet is 2.2 gallons per minute. Most new kitchen faucets have an aerator, the screw-on tip of the nozzle on the faucet. Bathroom faucets have a more restrictive flow of 1.5 or even . 5 gallons per minute.

### What should my water flow rate be?

The easiest way to get a fairly accurate measure of your water flow rate is to time yourself filling up a bucket. So for example if you fill up a 10 litre bucket in 1.5 minutes, then your flow rate will be: 10/1.5 = 6.66 Litres per minute. Don’t get confused between flow rate and pressure.

### How fast do wells refill?

It depends on the source of the well water. It should be a minimum of 600 gallons within a two-hour period, or about 5 gallons per minute for 2 hours.

### What size pump do I need for my well?

25 – 400 feet use a 4-inch submersible pump To size your pump you’ll need to estimate your family’s water needs. A typical 3 to 4 bedroom home requires between 8 and 12 gallons per minute (GPM). To estimate your family’s needs simply count all of the water fixtures in your home.

### How do you increase gpm on a well?

Yet another option is to install a small storage tank. The water flows from the well into a storage tank first, then a booster pump with adequate flow rate can boost up the pressure after the tank. Count the gallons “drawn down” from the pressure tank and the time between the cut-in and cut-off cycle of the well pump.

### How do I calculate my well recovery rate?

Multiply the gallons per foot of well bore times the footage of water level rebound during the recovery. Then divide the result by the time of this recovery to a yield estimated rate of gallons per minute.

### What is good water pressure for a well?

between 40 and 60 psi

### How much bleach do you use to shock a well?

Mix 2 quarts bleach in 10 gallons of water; pour into well. Connect a garden hose to a nearby faucet and wash down the inside of the well. Open each faucet and let the water run until a strong chlorine odor is detected, then turn it off and go to the next one. Don’t forget outdoor faucets and hydrants.